Hudson-robotics LabLinx Uživatelský manuál

STACKLINK LABLINX USER MANUAL 10 Stern Avenue, Springfield, NJ 07081 Tel: 973-376-7400  Fax: 973-376-8265

StackLink User Manual Hudson Robotics, Inc. 6 Setting up the StackLink  Remove the StackLink from the carton and carefully remove the protective

StackLink User Manual Hudson Robotics, Inc. 7 Setting Up StopLink(s)  Position the StopLink in the desired location on the track and secure its

StackLink User Manual Hudson Robotics, Inc. 8 StopLink Positions 7-10 Figure 10 Figure 11 Clamp Bars securing tracks

StackLink User Manual Hudson Robotics, Inc. 9 Figure 12 Connect Power Cord & Communication Cable: Note: Power switch must be turned OFF

StackLink User Manual Hudson Robotics, Inc. 10 CHAPTER 3-StackLink Software Brief Description of Software Hudson's standard StackLink applic

StackLink User Manual Hudson Robotics, Inc. 11 Configuring a Workcell  Click on the Configure Workcell icon on the screen.  Click and dra

StackLink User Manual Hudson Robotics, Inc. 12  Click the Setup button under the StackLink icon.  Select each StopLink position(s) with

StackLink User Manual Hudson Robotics, Inc. 13  NOTE: Be sure to match the correct instrument nest name from the pull down menu or errors will o

StackLink User Manual Hudson Robotics, Inc. 14 Click on the ‘Edit Plate’ button to change the parameters of a previously defined plate, or click

StackLink User Manual Hudson Robotics, Inc. 15 CHAPTER 5-StackLink Components DriveLink System The StackLink’s elevator and plate handling comp

StackLink User Manual Hudson Robotics, Inc. i Contents CHAPTER 1-Introduction ...

StackLink User Manual Hudson Robotics, Inc. 16  Instrument alignment bases – Enables the instruments to be locked to the TrackLink so

StackLink User Manual Hudson Robotics, Inc. 17 CHAPTER 6-Hardware Specifications General Note: Specifications are subject to change without no

StackLink User Manual Hudson Robotics, Inc. 18  Internal Air Tubing: Parflex Polyurethane tubing 1/16” ID, 1/8” OD Parflex Polyurethane tubing 2

StackLink User Manual Hudson Robotics, Inc. 19 CHAPTER 7-Maintenance Maintenance WARNING- -  Qualified personnel can perform all maintenance p

StackLink User Manual Hudson Robotics, Inc. 20  Using a small flat head screwdriver, gently pry the fuse holder tray away from its housing to acc

StackLink User Manual Hudson Robotics, Inc. 21 Appendix A: Hudson's LabLinx Communications and Command Set Version 1.0 Hudson's L

StackLink User Manual Hudson Robotics, Inc. 22 currently unspecified. There is currently no message indicating that the command queue has been ove

StackLink User Manual Hudson Robotics, Inc. 23 StackLink Command Set The StackLink Unit recognizes the following commands: 1. ACKNOWLEDGESEND Th

StackLink User Manual Hudson Robotics, Inc. 24 dispense double-flanged or otherwise oddly shaped plates. This time is set using the SETDISPENSEDEL

StackLink User Manual Hudson Robotics, Inc. 25 8. GETPOSNUM {Position Name} GETPOSNUM will return the position value associated with the specified

StackLink User Manual Hudson Robotics, Inc. ii CHAPTER 7-Maintenance ...

StackLink User Manual Hudson Robotics, Inc. 26 12. NAMEPOS {Position Number}, {Position Name} The NAMEPOS command assigns the indicated name to the

StackLink User Manual Hudson Robotics, Inc. 27 16. RETURN [Stacks] RETURN will place plates located under the indicated stacks into the stacks. Th

StackLink User Manual Hudson Robotics, Inc. 28 20. SETIP {IP Address} SETIP will set the IP address of the unit. This change is immediate and may

StackLink User Manual Hudson Robotics, Inc. 29 23. SHIFT {Direction}, [Positions], [Receive] The SHIFT command will move plates one position in the

StackLink User Manual Hudson Robotics, Inc. 30 Error Code Description The PlateCrane controller will report one of the following response codes at

StackLink User Manual Hudson Robotics, Inc. iii WARNING- -  This product may be used only in the manner described in this manual. When used o

StackLink User Manual Hudson Robotics, Inc. 1 CHAPTER 1-Introduction Overview The StackLink (Figure 1) is an automated microplate stacker, which

StackLink User Manual Hudson Robotics, Inc. 2 Tracklink StopLink Figure 2

StackLink User Manual Hudson Robotics, Inc. 3  The Computer has the recommended number of working serial ports (You can Purchase USB-to-serial co

StackLink User Manual Hudson Robotics, Inc. 4 Chapter 2-Installation Unpacking the StackLink WARNING- -  Power switch must be turned OFF durin

StackLink User Manual Hudson Robotics, Inc. 5 DO NOT DISCARD the StackLink carton. This carton has been specially created for this product and m